Whole-Home Filtration in Scottsdale, Sized From Your Test

What a Whole-Home Filter Does, and What It Doesn't

This kind of system treats water at the point where it enters your home. We mount it on the main supply line, upstream of the water heater, so everything that flows into the house passes through it first. Inside the tank is a bed of activated or catalytic carbon. Chlorine, chloramine and many of the organic compounds that cause off tastes and smells cling to the carbon surface as water moves through. A sediment cartridge mounted before the tank holds back grit that would otherwise coat the carbon and shorten its life.

Hardness is a different problem. Calcium and magnesium move right through carbon, so if white scale on fixtures is what bothers you, a water softener handles that, and many homes run both in series. For the purest drinking water at a single faucet, reverse osmosis under the sink goes beyond what carbon can do. Testing comes first so you know which of these your water really needs.

What Your Installation Includes

Sediment prefilter

A replaceable cartridge in its own housing catches sand, rust flakes and pipe scale before they reach the carbon. It keeps the media bed from packing down, and it is the part you will swap on a routine schedule.

Carbon media tank sized to flow

We size the tank by your peak flow in gallons per minute, not by square footage. Water needs enough contact time in the carbon bed to be filtered properly, and an undersized tank lets chlorine slip through when two showers run at once.

Control valve and bypass

Backwashing systems get a control valve that reverses flow on a schedule to lift and rinse the carbon bed. A bypass valve lets you isolate the filter for service while the rest of your home keeps its water.

Plumbing tie-in and bonding

We cut into the main line with full-port shutoffs and unions so the system can be removed cleanly later. If your home has metal supply pipe, we add a bonding jumper across the new section so the electrical ground path stays continuous.

Installation as part of the system

Installation is included with our water treatment systems. There is no separate labor bill stacked on top of the equipment.

Signs Your Home Would Benefit From Whole-Home Filtration

• A pool smell from the shower

  Hot water releases chlorine into the air as steam. If the bathroom smells like a pool, the disinfectant is reaching every tap, not just the one you drink from.

• Dry skin or brittle hair after bathing

  Many people notice their skin and hair feel better on filtered water. A countertop pitcher can't help here because the shower is fed straight from the main line.

• Coffee and ice taste off

  Your refrigerator's small inline filter may be overloaded or overdue. Treating water at the point of entry takes that load off and improves the water the fridge and coffee maker receive.

• Grit in faucet aerators

  Unscrew an aerator and look at the little screen. Sand or dark flakes trapped there mean particles are traveling through your plumbing, and a cartridge at the main line catches them before they wear on valves and appliance inlets.

• You're adding a softener anyway

  Many homes have a pre-plumbed loop in the garage meant for water treatment. Putting carbon ahead of a softener in that loop shields the softener resin from chlorine, which slowly breaks resin beads down.

How the Work Runs, From Test to Startup

1. 1

   Free water test and walkthrough

   We test your water at no charge and with zero obligation, then look at where your main line enters, the pipe material and size, and where a drain line can run. The results tell us whether carbon alone is enough or whether a softener should sit downstream.

2. 2

   Installed pricing by phone

   You get the installed system price over the phone, with the tank size, media type and plumbing work named. Nothing is added after the fact.

3. 3

   Install day

   We shut off the main, cut in the shutoffs, bypass and unions, set the prefilter and tank, and run the backwash drain to an approved air gap. Floors and the work area are covered, and old pipe and packaging leave with us.

4. 4

   Rinse, leak check and handoff

   Fresh carbon sheds a fine black powder at first, so we run the bed to drain until the water comes out clear. Then we go over every joint for drips, test pressure at a faucet, and show you how the bypass and prefilter work so routine upkeep is something you can do yourself.

What Moves the Price of a Whole-Home System

Most of the cost comes from two things: how much water your home moves at peak, and how easy it is to reach the main line. We give you installed system pricing by phone after the free test, so you see the full figure before any work is scheduled.

Peak flow and tank size

More bathrooms and simultaneous use need a larger carbon bed to keep enough contact time. Tank size drives both equipment cost and media replacement cost later.

Catalytic or standard carbon

Catalytic carbon handles chloramine far better than standard activated carbon and costs more. Your test results decide which one makes sense.

Existing loop or new plumbing

A pre-plumbed treatment loop shortens the job. Without one, we run new pipe from the main, and the length, pipe material and wall access all add labor.

Drain and placement

Backwashing tanks need a drain within reach. Systems placed outdoors also need shading or a cover, since direct sun degrades plastic housings.